Scanning wind-vector scatterometers with two pencil beams

A scanning pencil-beam scatterometer for ocean windvector determination has potential advantages over the fan-beam systems used and proposed heretofore. The pencil beam permits use of lower transmitter power, and at the same time allows concurrent use of the reflector by a radiometer to correct for atmospheric attenuation and other radiometers for other purposes. The use of dual beams based on the same scanning reflector permits four looks at each cell on the surface, thereby improving accuracy and allowing alias removal. Simulation results for a spaceborne dual-beam scanning scatterometer with a 1-watt radiated power at an orbital altitude of 900 km is described. Two novel algorithms for removing the aliases in the windvector are described, in addition to an adaptation of the conventional maximum likelihood algorithm. The new algorithms are more effective at alias removal than the conventional one. Measurement errors for the wind speed, assuming perfect alias removal, were found to be less than 10%

Radar spectral measurements of vegetation

Spectral data of 4-8 GHz radar backscatter were gathered during the 1972 growing season at look angles between 0 and 70 deg and for all four possible polarization linear combinations. The data covers four crop types (corn, milo, alfalfa, and soybeans) and a wide range of soil moisture content. To insure statistical representation of the results, measurements were conducted over 128 fields corresponding to a total of about 40,000 data points. The use of spectral response signatures to separate different crop types and to separate healthy corn from blighted corn was investigated

Wave speeds in the corona and the dynamics of mass ejections

A disturbance or coronal mass ejection being advected by the solar wind will expand at the fastest local characteristic speed - typically approximately the fast-mode speed. To estimate this characteristic wave speed and the velocity field in the ambient corona, it is necessary to know the magnetic field, temperature, and density. Only the density is known from coronal observations. The temperature, magnetic field, and velocity are not yet directly measured in the outer corona and must be estimated from a model. In this study, it is estimated that the magnetic field, solar wind velocity, and characteristic speeds use the MHD model of coronal expansion between 1 and 5 solar radii (R solar radii) with a dipole magnetic field at the base. This model, for a field strength of about 2 gauss at the base, gives flow speeds at low latitudes (near the heliospheric current sheet) of 250 km/s at 5 R solar radii and, 50 km/s at 2 solar radii, and fast-mode speeds to 400 to 500 km/s everywhere between 2 and 5 solar radii. This suggests that the outer edge of a velocity of mass ejection reported by MacQueen and Fisher (1983) and implies that the acceleration mechanism for coronal mass ejections is other than simple entrainment in the solar wind

Creep behavior of niobium alloy PWC-11

The high vacuum creep and creep-rupture behavior of a Nb-1Zr-.1C alloy (PWC 11) was investigated at 1350 and 1400 K with an applied stress of 40 MPa. The material was tested in the following four conditions: annealed (1 hr 1755 K/2 hr 1475 K); annealed plus EB welded; annealed plus aged for 1000 hr at 1350 or 1400 K; and annealed, welded, and aged. It was found that the material in the annealed state was the most creep-resistant condition tested, and that aging the alloy for 1000 hr without an applied stress greatly reduced that strength; however, it was still approximately three times as creep resistant as Nb-1Zr. Additionally, the EB weld region was stronger than the base metal in each condition tested, and phase extraction of the dispersed precipitate revealed the presence of a 70%ZrC-30%NbC cubic monocarbide phase

The effect of electron beam welding on the creep rupture properties of a Nb-Zr-C alloy

Creep rupture tests of electron beam welded PWC-11 sheet were conducted at 1350 K. Full penetration, single pass welds were oriented transverse to the testing direction in 1 mm thick sheet. With this orientation, stress was imposed equally on the base metal, weld metal, and heat-affected zone. Tests were conducted in both the postweld annealed and aged conditions. Unwelded specimens with similar heat treatments were tested for comparative purposes. It was found that the weld region is stronger than the base metal for both the annealed and aged conditions and that the PWC-11 material is stronger in the annealed condition than in the aged condition

Quantitative Analysis of Electrotonic Structure and Membrane Properties of NMDA-Activated Lamprey Spinal Neurons

Parameter optimization methods were used to quantitatively analyze frequency-domain-voltage-clamp data of NMDA-activated lamprey spinal neurons simultaneously over a wide range of membrane potentials. A neuronal cable model was used to explicitly take into account receptors located on the dendritic trees. The driving point membrane admittance was measured from the cell soma in response to a Fourier synthesized point voltage clamp stimulus. The data were fitted to an equivalent cable model consisting of a single lumped soma compartment coupled resistively to a series of equal dendritic compartments. The model contains voltage-dependent NMDA sensitive (INMDA), slow potassium (IK), and leakage (IL) currents. Both the passive cable properties and the voltage dependence of ion channel kinetics were estimated, including the electrotonic structure of the cell, the steady-state gating characteristics, and the time constants for particular voltage- and time-dependent ionic conductances. An alternate kinetic formulation was developed that consisted of steady-state values for the gating parameters and their time constants at half-activation values as well as slopes of these parameters at half-activation. This procedure allowed independent restrictions on the magnitude and slope of both the steady-state gating variable and its associated time constant. Quantitative estimates of the voltage-dependent membrane ion conductances and their kinetic parameters were used to solve the nonlinear equations describing dynamic responses. The model accurately predicts current clamp responses and is consistent with experimentally measured TTX-resistant NMDA-induced patterned activity. In summary, an analysis method is developed that provides a pragmatic approach to quantitatively describe a nonlinear neuronal system

Statistics of Ku-band microwave response of the United States with a satellite borne radiometer/scatterometer

The author has identified the following significant results. The Skylab S-193 radiometer/scatterometer collected thousands of measurements of scattering coefficient and brightness temperature over various parts of the United States during the summer of 1973 at angles of incidence between vertical and about 45 deg. These measurements have been combined to produce histograms of the response at each of several angles within this range, and to establish average scattering coefficient vs angle curves with 10% and 90% exceedance levels as well. The variation of the radiometric measurements is primarily in the region from 255 K to 285 K, with very few measurements giving higher values, but a significant, though small, number giving values down to and even below 200 K. The scattering coefficient varies, for the mean, from about 0 db at 1 deg off vertical to a low in the neighborhood of -10 db at 45 deg. The variability of the scattering coefficient measurements with this coarse resolution sensor is surprisingly small. The number of distinguishable levels is slightly more for the scatterometer than for the radiometer, but the amount of variation in brightness temperature caused by the physical temperature of the ground is enough so that the scatterometer can be used to distinguish significantly more meaningful levels than the radiometer

The Renal Lymphatics - an Important Fluid Transport System

Study of renal lymph fluid transport syste

Turbofan forced mixer lobe flow modeling. Part 3: Application to augment engines

Military engines frequently need large quantities of thrust for short periods of time. The addition of an augmentor can provide such thrust increases but with a penalty of increased duct length and engine weight. The addition of a forced mixer to the augmentor improves performance and reduces the penalty, as well as providing a method for siting the required flame holders. In this report two augmentor concepts are investigated: a swirl-mixer augmentor and a mixer-flameholder augmentor. Several designs for each concept are included and an experimental assessment of one of the swirl-mixer augmentors is presented